DMP 70 (Reference-Nr. 051428)

•  
  Reference number 051428

  Manufacture Year 2019

  Operation Hours not applicable

• Vendor

  DMG MORI EMEA Holding GmbH
  Walter-Gropius-Str.7
  80807 München

  Germany

  

• Main Category

  Metal working machines

• Category

  Machining centres

• Type of Machine

  Machining Centers (Vertical)

• Manufacturer

  DMG MORI

• Control

  Siemens

• Description

  
  

  General
  High dynamic Vertical Drill-Tap centre with best milling performance; Control: 3D-control Siemens 840D sl Operate
  Working area 1
  Longitudinal	700 mm
  Cross	420 mm
  Vertical	380 mm
  Technical Data
  Feed rate longitudinal/transverse/vertical	60000/60000/60000 mm/min
  Rapid traverse longitudinal/transverse/vertical	60/60/60 m/min

• Specification

  
  

  Main drive	Drive power (100% DC) 6 kW
  	Drive power (40% DC) 8,5 kW
  	Clamping System ISO 7388-3 - JD30
  	Spindle taper BT 30
  	Speed range 20 - 10000 rpm
  	Torque (40% DC) 48 Nm
  	Torque (100% DC) 41 Nm
  Integrated swivel rotary table simultaneous	Integated swivel rotary table 5-Axis simultaneous mode! Torque drives incl. direct measuring in A- and C-Axis Swivel range A-Axis -120 / + 100 degrees Max. load C-axis 100kg Table diameter C-Axis d290mm Inclusive Software package Sinumerik Mdynamics 5-ax
  Rotary joint, 4 channels	Rotary joint for integrated swivel rotary table with torque drives 4- channels, in Standard 2x for air, 2x for oil Including fix plate and fast coupling at machine rear side
  Clamping pneumatic, one circuit	Clamping pneumatic 1-circuit Including 2x 3/2 way valve
  Tool magazine 25 places	Tool magazine 25 places (suitable for inclusion in the tool spindle) Chip-to-chip time 1.6 sec
  Production package band filter ICS 40bar	Paper band filter ICS 40bar includes: Paper band filter 40bar/ 23l/min Additional tank 600l Chip conveyor useable for fine chips (self cleaning slotted filter) Discharge height: 600mm; Tank volume 200l Flushing in working room Spray gun for swarf removal
  Air blast through spindle centre	Air blast through spindle center via M-Command; maintained air with small Oil portion Due to needed lead through in main spindle only with swarf removal package ICS possible!
  Preparation 3D Quickset	Machine preparation for use of the 3D quickSET Toolkit. included is the Softwareoption for 3D quickSET for one machine. 5 axis machine configurations (only with option touch probe)
  Signal lamp 4-colour	Signal lamp, 4 colours
  DMG MORI Interface PROFIBUS Right	DMG MORI Interface PROFIBUS loading door at right machine side PROFIBUS communication between robot and machine for loading cycle 2 channel safety circuits Only in combination with an additional clamping method option!.
  Operation mode 4	Operation mode 4 Process monitoring in the production Manual intervention with open doors of machining area. Release after check list has been filled in.
  Tropical package	Package for tropical climate for ambient temperature max. 50°Celsius: includes active cooling for electrical cabinet, active cooling main spindle drive / motor spindle
  Special equipment	RMS-Sensor
  Workpiece loading & unloading system WH 3 CELL	Workpiece loading & unloading system WH 3 CELL with 6-axis industrial robots and workpiece carrier storing system (paternoster); maximum possible workpiece weight of 3 kg, maximum workpiece size 100 x 100 x 50 mm Robot FANUC LR Mate 200 iD/7L PROFIBUS in
  WH 3 CELL Integration kit for DMP 35/70	WH 3 CELL Integration kit for DMP 35/70 Machine-specific adaptation for the protective housing on one DMP 35/70
  Dual gripper PGN 80 (without gripper fingers)	Dual gripper Type Schunk PGN 80 with 8 mm travel per jaw (gripper fingers not included!)
  Gripper system Schunk PGN-plus 80	Gripping device Schunk PGN-plus 80

• State

  Used